Videos

Tacker gun for 40mm and 60mm underfloor heating pipe clips
Tacker Gun for 40mm & 60mm Clips: Clip pipe standing up (video guide)
A stand-up tacker gun that fixes underfloor heating pipe to insulation board with barbed pipe clips, so you can work along the loop without kneeling. Made for the MaxHeatUFH High... Read more...
Red uncoupling membrane roll for tiling over electric underfloor heating
Uncoupling Membrane, 1m Roll: Helps stop cracked tiles over loose electric heating cable (video guide)
An uncoupling membrane for tiled floors over electric underfloor heating. It separates the tiles from movement in timber, new screed or mixed subfloors, helping stop cracked tiles and grout, and... Read more...
Roll of printed grid membrane for underfloor heating, 1.2m wide
UFH Grid Membrane 1.2m Wide: Set out pipe centres without measuring (video guide)
A printed grid membrane that rolls out over the insulation before screeding. Set out 100, 150 or 200mm centres without measuring every run, and give tacker clips a tough layer... Read more...
UFH manifold 90 degree elbow connector set, 1 inch, flow and return
90° Elbow Connector Set 1": Pump pack round the corner, no extra pipework (video guide)
A 1" 90° elbow connector set that mounts the pump and blending unit at right angles to the manifold, for example around a corner in a cupboard, with no extra... Read more...
Ultra Prime IT multi surface primer, 5 litre container
Ultra Prime IT Primer 5L: Primer, sealer and bonding aid in one (video guide)
Ultra Prime IT from Ultra TileFix is a water-based acrylic primer, sealer and bonding aid for porous and non-porous subfloors. Use it before self-adhesive panels, levelling compound or tile adhesive. Read more...
MLCP press fit wall-plated female elbow with fixing plate and BSP outlet
MLCP Press Wall-Plated Female Elbow: a solid outlet for taps and showers (video guide)
The MaxHeatUFH MLCP press fit wall-plated female elbow is a 90° press elbow with a female BSP outlet and a fixing plate. Screw it to a wall, timber noggin or... Read more...
Replacement plug-in power cable with moulded connector for a UFH circulating pump
Wilo Pump Power Cable: Plug-in lead for Wilo A-rated UFH pumps (video guide)
A plug-in power cable for Wilo A-rated underfloor heating pumps, including the Wilo 6m pump on MaxHeatUFH pump packs. The moulded connector pushes straight in, so it makes a handy... Read more...
Heatmiser wireless air sensor, small white wall-mounted room sensor
Heatmiser Wireless Air Sensor: room sensing with no cable to run (video guide)
The Heatmiser wireless air sensor measures room temperature away from the thermostat, with no cable to run. Use it where the thermostat is in the wrong spot, or in large... Read more...
MLCP press fit to copper adaptor with plain brass tail
MLCP Press to Copper Brass Tail: tie multilayer into existing copper (video guide)
The MaxHeatUFH MLCP press fit to copper brass tail has a U-profile press end for multilayer pipe and a plain brass tail sized for copper. The tail goes into a... Read more...
Wilo A-rated UFH circulating pump with 6m head and power cable
Wilo A-Rated UFH Pump 6m: Direct replacement for our pump packs (video guide)
A Wilo high-efficiency circulator for underfloor heating manifolds and domestic heating circuits. The A-rated ECM motor keeps running costs down, and it's a direct replacement for the pump on MaxHeatUFH... Read more...
MLCP press fit unequal reducing tee for multilayer pipe
MLCP Press Fit Unequal Tee: reduce and branch in one fitting (video guide)
The MaxHeatUFH MLCP press fit unequal tee branches multilayer pipe where the run and branch are different sizes, such as taking 16mm circuits off a 20, 25 or 32mm main.... Read more...
UFH non-mixing pump set with Wilo A-rated 6m pump
Non-Mixing Pump Set, Wilo 6m: No blending valve for heat pumps (video guide)
For manifolds on a heat pump or other low-temperature source, where the flow is already at floor temperature. There's no blending valve, so nothing holds back the flow temperature. It... Read more...
MLCP press fit swivel female elbow with loose BSP nut
MLCP Press Swivel Female Elbow: tighten the nut, not the pipe (video guide)
The MaxHeatUFH MLCP press fit swivel female elbow is a 90° press elbow with a loose female BSP swivel nut. You tighten the nut, not the pipe, so loops stay... Read more...
MLCP press fit male straight union with male BSP thread
MLCP Press Male Straight Union: multilayer pipe to male BSP (video guide)
The MaxHeatUFH MLCP press fit male straight union has a U-profile press end for multilayer pipe and a male BSP thread on the other end. Use it to connect into... Read more...
MTA terminal adaptor with compression socket for 16mm pipe and 1/2 inch thread
MTA Terminal Adaptor 16mm x 1/2": compression joint, no press (video guide)
The MaxHeatUFH MTA terminal adaptor connects 16mm underfloor heating pipe to valves or fittings. A compression socket takes the pipe, and a 1/2" male thread makes the connection. Read more...
Heatmiser UH8-RF 8 zone wireless wiring centre with manual, angled view
Heatmiser UH8-RF Wiring Centre: 8 zones, no thermostat cables (video guide)
The Heatmiser UH8-RF is an eight zone wireless wiring centre for underfloor heating. It takes signals from battery thermostats such as the Slimline-RF and neoAir, so there are no thermostat... Read more...
MLCP press fit 90 degree male elbow with male BSP thread
MLCP Press Fit Male Elbow: saves you an elbow and an adaptor (video guide)
The MaxHeatUFH MLCP press fit male elbow is a 90° fitting with a U-profile press end and a male BSP thread. Use it where the pipe arrives at a right... Read more...
UFH non-mixing pump set with Bastion A-rated 7.5m pump
Non-Mixing Pump Set, Bastion 7.5m: Higher head for longer loops (video guide)
For manifolds on a heat pump or other low-temperature source, where the flow is already at floor temperature. There's no blending valve, so nothing holds back the flow temperature. The... Read more...
Self-adhesive underfloor heating pipe clip rail, 1 metre length
Self-Adhesive Pipe Clip Rail 1m: No screws, even pipe centres (video guide)
A 1m self-adhesive pipe clip rail for underfloor heating, so no screws are needed. The lengths interlock end to end to make any run, and hold every pipe in line... Read more...
Tuskbond FD170 spray contact adhesive, 500ml aerosol can
Tuskbond FD170 Spray Adhesive 500ml: No mixing, brushes or trowels (video guide)
Tuskbond FD170 is a spray contact adhesive in a 500ml can for bonding insulation boards and membranes on underfloor heating jobs. No mixing, brushes or trowels, and it's easy to... Read more...
Heatmiser UH8-N 8 zone 12V network wiring centre, front view
Heatmiser UH8-N Wiring Centre: 8 zones for 12V thermostats (video guide)
The Heatmiser UH8-N is an eight zone wiring centre made for 12V thermostats such as the neoStat 12V. It runs from 230V and powers the thermostats itself, and when any... Read more...
MLCP press fit reducing straight connector for joining two multilayer pipe sizes
MLCP Press Reducing Straight Connector: two pipe sizes, one joint (video guide)
The MaxHeatUFH MLCP press fit reducing straight connector joins multilayer pipe of two different sizes in a straight line, for example, stepping a 20mm main down to 16mm for a... Read more...
Roll of reflective aluminium foil insulation for underfloor heating, 1m x 50m
Reflective Foil Insulation Roll 1m x 50m: Reflects heat into the floor (video guide)
A 1m x 50m reflective foil insulation roll for underfloor heating. The foil face reflects heat up into the floor, and the roll acts as a moisture and vapour barrier.... Read more...
Ratchet plastic pipe cutter for pipe up to 52mm
Ratchet Plastic Pipe Cutter 52mm: Less effort on bigger pipe (video guide)
A ratchet pipe cutter for PVC, PPR, PERT-EVOH, PEX and multilayer pipe up to 52mm. The hardened steel blade gives a clean, square cut, and the ratchet means less effort... Read more...
MaxHeatPro foil-faced EPS underfloor heating panel, 1200 x 600mm
MaxHeatPro Foil-Faced EPS Panel: float under wood or tile direct (video guide)
MaxHeatPro is a grooved EPS underfloor heating panel with a 100 micron aluminium foil face that spreads heat from the pipe across the floor. Lay it floating under wood or... Read more...
Heatmiser UH4 4 zone underfloor heating wiring centre, angled view
Heatmiser UH4 Wiring Centre: 230V, up to 4 UFH zones (video guide)
The Heatmiser UH4 is a 230V wiring centre for smaller underfloor heating systems, up to four zones. It links mains room thermostats to the manifold actuators, then calls the pump... Read more...
Heatmiser UH8 8 zone underfloor heating wiring centre, angled view
Heatmiser UH8 Wiring Centre: 230V, up to 8 UFH zones (video guide)
The Heatmiser UH8 is a 230V underfloor heating wiring centre for up to eight zones, and the most common choice for whole-house wet UFH. Each mains thermostat opens its actuators,... Read more...
Pressure gauge end unit for an underfloor heating manifold
Manifold Pressure Gauge End Unit: system pressure at a glance (video guide)
The MaxHeatUFH manifold pressure gauge end unit fits on the end of a manifold bar and shows system pressure at a glance. Check the fill and spot a pressure drop... Read more...
UFH non-mixing pump set for a manifold, supplied without pump
Non-Mixing Pump Set, No Pump: Heat pump pack, fit your own pump (video guide)
For manifolds on a heat pump or other low-temperature source, where the flow is already at floor temperature. There's no blending valve, so nothing holds back the flow temperature. Fit... Read more...
MLCP press fit female straight union with female BSP thread
MLCP Press Female Straight Union: multilayer pipe to female BSP (video guide)
The MaxHeatUFH MLCP press fit female straight union connects multilayer pipe to male-threaded valves, manifold tails and appliances, with a U-profile press end on one side and a female BSP... Read more...
UFH non-mixing pump set with Bastion A-rated 6m pump
Non-Mixing Pump Set, Bastion 6m: No blending valve for heat pumps (video guide)
For manifolds on a heat pump or other low-temperature source, where the flow is already at floor temperature. There's no blending valve, so nothing holds back the flow temperature. It... Read more...
MLCP press fit lever ball valve with press ends and coloured lever
MLCP Press Fit Lever Ball Valve: full bore, no flame, no threads (video guide)
The MaxHeatUFH MLCP press fit lever ball valve is a full-bore brass isolating valve with U-profile press ends on both sides. Isolate UFH circuits, manifold flow and return, heating zones... Read more...
Pre-insulated PEX-AL-PEX multilayer pipe coils in red for flow and blue for return
Pre-Insulated Multilayer Pipe: Red flow, blue return, no lagging (video guide)
Multilayer pipe with insulation already fitted, red for flow and blue for return. Use it for runs like boiler or heat pump to the manifold, with no separate lagging to... Read more...
MLCP press fit tee with 1/2 inch female BSP branch
MLCP Press Fit Female Tee: take a vent, gauge or drain off the run (video guide)
The MaxHeatUFH MLCP press fit female tee has press ends on the run and a 1/2" female BSP branch. Take a drain cock, air vent, gauge, sensor pocket or tap... Read more...
Wilo pump and blending valve mixing unit for an underfloor heating manifold
Blending Valve Pump Pack, Wilo 6m: Bolt-on 20 to 55°C, no valve wiring (video guide)
A pre-assembled blending valve unit that bolts onto the manifold. The wax-capsule valve holds the floor at 20 to 55°C, with no wiring. It comes with a Wilo A-rated 6m... Read more...
MLCP press fit 90 degree female elbow with female BSP thread
MLCP Press Fit Female Elbow: turns and connects in one fitting (video guide)
The MaxHeatUFH MLCP press fit female elbow is a 90° fitting with a U-profile press end and a fixed female BSP thread. It suits male-threaded valves, manifold connections, pumps and... Read more...
Heatmiser Thimble Sensor, small discreet wired room temperature sensor
Heatmiser Thimble Sensor: discreet room sensing, no stat on show (video guide)
The Heatmiser Thimble is a small wired room temperature sensor for rooms where the client doesn't want a thermostat on the wall, such as a feature wall, bathroom or show... Read more...
MaxHeatPanel routed XPS underfloor heating board with grooves, 1200 x 600mm
MaxHeatPanel Routed XPS Board: tile direct, no screed to wait for (video guide)
MaxHeatPanel is a CNC-routed XPS insulation board for wet underfloor heating on solid floors. Bond it down, press the pipe into the grooves and tile directly onto the board, with... Read more...
Plastic star pipe reaming tool for 12mm, 16mm and 20mm pipe
Pipe Reaming Tool (Star Reamer): Re-rounds and deburrs the bore (video guide)
A star reamer for multilayer, PERT-EVOH and PEX pipe after cutting. It re-rounds the bore and deburrs the inside edge, so fittings seat without damaging the O-rings. Read more...
Underfloor heating manifold flow meter with clear sight glass
Manifold Flow Meter: see and balance the flow in each loop (video guide)
The MaxHeatUFH manifold flow meter sits on the flow bar and shows how much water is going round each loop, from 0 to 5 litres a minute. Use it to... Read more...
UFH manifold blending valve pump pack with Grundfos UPM3 Auto pump, 20–55°C
Blending Valve Pump Pack, UPM3 Auto: Pump sets itself to the system (video guide)
A pre-assembled blending valve unit that bolts onto the manifold. The wax-capsule valve holds the floor at 20 to 55°C, with no wiring. The Grundfos UPM3 Auto uses AUTOADAPT to... Read more...
Underfloor heating pipe support bend for a 90 degree turn
Pipe Support Bend: Supported 90° turn up to the manifold (video guide)
A pipe support bend that holds the pipe in a smooth, supported 90° turn where it rises from the floor to the manifold, so it doesn't kink or flatten. Sold... Read more...
UFH manifold blending valve pump pack fitted with Grundfos UPM3 Flex pump
Blending Valve Pump Pack, UPM3 Flex: Heat source sets pump speed by PWM (video guide)
A pre-assembled blending valve unit that bolts onto the manifold. The wax-capsule valve holds the floor at 20 to 55°C, with no wiring. With the Grundfos UPM3 Flex, the heat... Read more...
MLCP press fit equal tee with three press ends for multilayer pipe
MLCP Press Fit Equal Tee: an inspection window on every end (video guide)
The MaxHeatUFH MLCP press fit equal tee takes a branch off a multilayer pipe run, with all three ends the same size, for heating, underfloor heating, and hot and cold... Read more...
Heatmiser Touch white touchscreen programmable room thermostat
Heatmiser Touch / Touch Carbon: 230V touchscreen thermostat (video guide)
The Heatmiser Touch is a 230V touchscreen programmable thermostat for underfloor heating and radiator zones. Choose white, or Touch Carbon with a dark-background screen: the features are the same. Read more...
MLCP press fit equal straight connector, brass body with stainless press sleeves
MLCP Press Equal Straight Connector: the everyday multilayer coupling (video guide)
The MaxHeatUFH MLCP press fit equal straight connector joins two lengths of multilayer pipe of the same size. It's the everyday coupling for manifold tails, radiator circuits and plumbing runs,... Read more...
MLCP press fit 90 degree equal elbow for multilayer pipe
MLCP Press Fit Equal Elbow: a 90° turn in less space than a bend (video guide)
The MaxHeatUFH MLCP press fit equal elbow turns a multilayer pipe run through 90°, with the same pipe size on both ends. You get a full turn in much less... Read more...
Pipe decoiler for laying underfloor heating pipe from the coil
Pipe Decoiler: Lay UFH pipe alone with no twists (video guide)
A pipe decoiler that holds a coil of underfloor heating pipe and turns as you pull, so the pipe pays out without twisting or tangling. Loops go down faster and... Read more...
Heatmiser wired temperature sensor probe with cable
Heatmiser Sensor Probe: wired remote air or floor sensor (video guide)
A wired remote sensor for Heatmiser thermostats that accept one, such as the Edge, Touch, neoStat V3 and neoStat WiFi. It can measure air or floor temperature and is designed... Read more...
MaxHeatUFH straight M-profile press jaw for electric hydraulic press tools
M-Profile Press Jaw 15-54mm: hardened steel, sold individually (video guide)
A straight, in-line M-profile press jaw for MaxHeatUFH electric hydraulic press tools, for copper and stainless steel M-profile press fittings. Hardened steel for daily use, sold individually so you buy... Read more...

Videos

167 video guides · newest first

Pipe & tools Tacker Gun for 40mm & 60mm Clips: Clip pipe standing up (video guide) Video · Watch Electric UFH Uncoupling Membrane, 1m Roll: Helps stop cracked tiles over loose electric heating cable (video guide) Video · Watch Pipe & tools UFH Grid Membrane 1.2m Wide: Set out pipe centres without measuring (video guide) Video · Watch Manifolds 90° Elbow Connector Set 1": Pump pack round the corner, no extra pipework (video guide) Video · Watch Panels & boards Ultra Prime IT Primer 5L: Primer, sealer and bonding aid in one (video guide) Video · Watch Fittings MLCP Press Wall-Plated Female Elbow: a solid outlet for taps and showers (video guide) Video · Watch Product guide Wilo Pump Power Cable: Plug-in lead for Wilo A-rated UFH pumps (video guide) Video · Watch Heatmiser Heatmiser Wireless Air Sensor: room sensing with no cable to run (video guide) Video · Watch Fittings MLCP Press to Copper Brass Tail: tie multilayer into existing copper (video guide) Video · Watch Product guide Wilo A-Rated UFH Pump 6m: Direct replacement for our pump packs (video guide) Video · Watch Fittings MLCP Press Fit Unequal Tee: reduce and branch in one fitting (video guide) Video · Watch Product guide Non-Mixing Pump Set, Wilo 6m: No blending valve for heat pumps (video guide) Video · Watch

Showing 12 of 167